Pipe Joint Sealant (Pipeseal PJS 44)

Send Inquiry

Product Code : 01

Brand Name : MAYUR PAINTS (INDIA) PVT. LTD.

Price And Quantity

Minimum Order Quantity
50
Unit of Measure
Kilograms/Kilograms

Price Range
80.00 - 350.00 INR

Product Specifications

Usage
Other
Color
Multicolor

Product Description

Pipe Joints Sealant:
As in so many areas of life, in the plumbing industry too, the speed of progress has quickened. New Pipe sealing systems, innovations in application technology, stricter environmental requirements and restrictive legislation, increasing pressure on cost-benefit ratios while maintaining an assurance of high quality - all these set new demands on manufacturing industry. Mayur Paints (India) Pvt. Ltd. has risen to the challenge by developing "Pipeseal PJS-44", a pipe joint sealant based on special polyesters, Pipeseal PJS-44 is a two pack pipe sealant which, because of its High Adhesive Strength and Low density, results in great cost saving. Compared to lead, consumption comes down appreciably, therefore using Pipeseal PJS-44 is most cost effective.

Pipeseal PJS-44 is most environment friendly and has very good Chemical and water resistance.

Ease of use:
Pipeseal PJS-44 is very simple to use as it does not require any heating. Just Mix one pouch (300 Gms. of black component with 200 Gms. of white component and fill in the joint.

The high solid content makes Pipeseal PJS-44 non shrinkable after drying.

Instructions for Jointing with PIPESEAL PJS-44

Open the packet of Black (300 gm) & white (200 gm) Chemical pastes.
Mix the two pastes well to make a smooth paste. A few (5/6) drops of water may be used if required , to facilitate uniform and homogenous mixing.
The Hemp Yarn (Rassi/Packing Rope) should be well packed in the joint and should be ready prior to PIPESEAL PJS-44 chemical sealant mixing. The space of 8-10 mm should be left for the chemical sealant (PIPESEAL PJS-44).
The chemical sealant as made at step (2) above should be applied in the space (8-10 mm) as per step (3) in a uniform manner.
Any excess sealant outside the socket should be removed and used immediately for other joints.
The joint has now set in and will harden in 20-40 minutes depending upon the weather conditions.

Advantages of PIPESEAL PJS-44 over Pig Lead

Disadvantages of using PIG Lead	Advantage of using Chemical Pipe Joint Sealant PIPESEAL PJS-44
Lead, being highly toxic is most environment unfriendly and is not being used in advanced countries such as USA, Europe, Japan etc.	Environment friendly as it has no toxic effect
It is hazardous to use lead as the same has to be heated to be brought into molten state and then poured into the pipe joints.	Easy and safe to use. Does not require any heating and is perfectly safe to handle.
The molten lead some times spills over and is known to cause serious burn injuries to the personnel handling the same.	No danger of pilferage as the joint sealant has no commercial value once the same is put in place
Lead pieces are easily removed by site labour and pilfered away and sold in the market for recycling.	No wastage as the entire sealant goes into the joint due to its easy handle ability
Pilferage of lead causes great loss to contractor / owner.	Used all over the world specifically in advanced countries such as Canada, North America. Europe, Japan etc.
A lot of lead is wasted due to spillage as there is no proper tool available for pouring molten lead into the pipe joints.	Cold application. Available in two pack system , just mix the contents of both the parts homogeneously and fill in the joint.
Using Lead works out nearly 6 times more expensive compared to PIPESEAL PJS-44	Low density of 1.95 gm/cc as compared to lead 11.35 gm/c.c., thereby consumption is much lower than that of lead. The resultant cost is very economical.
Lead being a poison causes Lead poisoning.	Has very good chemical and water resistance.